This easy and fun wall hanging is made using salvaged, repurposed lath.

Materials used:

Wood lath

Wood glue

18 Ga brad nails

Staple gun

3/4″ finishing nails

Chop saw

Hammer

Jig saw or table saw

T square and pen or pencil

24″ by 24″, 1/4″ thick fir (backing)

measure and mark the centre of your 24×24 backing board. No need to be perfect here as will be apparent as we go along.

Your first two pieces of lath need to be square. You need one square with the white side showing and the other square raw side showing. Because lath comes in various sizes, I measure. So my pieces were 1 1/2 inches and I made my cut lines at that measurement. At this stage we are just placing the pieces into spot, Do Not Glue down yet!

Now I am placing another piece of white lath and marking my cut line, as shown above. Cut along the cut line using chop saw and put into place. Again no glueing, that will come after all pieces have been cut and placed correctly.

Here I am showing where the next piece of white lath will be placed. Again line it up, mark and cut as shown above.

Next piece of lath is raw side up. Line up and mark as shown above. Cut the lath along your cut line and put into spot.

Next piece is again on the raw side, put into place marked and cut. As you can see we are basically working around our initial 2 squares, going round and round out towards the sides of the backer board.

Your going to keep going working around your piece. If you forget which side is next simply notice where 3 wood pieces are meeting together, that’s the side that needs the next piece. As shown above with the arrows.

Once you are down to your last pieces, you may need to adjust your centre. I simply put the next piece down and gently push it up till it is flush with the edge of the backer board.

Here I am showing the small piece of backer board left showing that will need to be trimmed off once all pieces have been secured down.

Here is where we begin to glue the pieces of cut and fit lath to our backer board. I like to start in the centre and careful not to disturb the surrounding pieces I pull up one piece at a time, glue and replace.

Once all pieces are glued down to the backer board I use my staple gun with small brads. I put one brad nail in each of the center squares and 2 nails in all other pieces, one on each end.

Now I use my jigsaw to clean up all the edges of the backer board, so the everything is flush together.

Here I am lining up and marking my first piece of trim that will act as the frame. Mark flush to your piece and cut.

Holding the piece vertically, I add glue, position the piece of lath and nail all along with 3/4″ finishing nails.

Continue until all four sides are framed in.

This is what the finished product should look like.

This is an example post, originally published as part of Blogging University. Enroll in one of our ten programs, and start your blog right.

You’re going to publish a post today. Don’t worry about how your blog looks. Don’t worry if you haven’t given it a name yet, or you’re feeling overwhelmed. Just click the “New Post” button, and tell us why you’re here.

Why do this?

• Because it gives new readers context. What are you about? Why should they read your blog?
• Because it will help you focus you own ideas about your blog and what you’d like to do with it.

The post can be short or long, a personal intro to your life or a bloggy mission statement, a manifesto for the future or a simple outline of your the types of things you hope to publish.

To help you get started, here are a few questions:

• Why are you blogging publicly, rather than keeping a personal journal?
• What topics do you think you’ll write about?
• Who would you love to connect with via your blog?
• If you blog successfully throughout the next year, what would you hope to have accomplished?

You’re not locked into any of this; one of the wonderful things about blogs is how they constantly evolve as we learn, grow, and interact with one another — but it’s good to know where and why you started, and articulating your goals may just give you a few other post ideas.

Can’t think how to get started? Just write the first thing that pops into your head. Anne Lamott, author of a book on writing we love, says that you need to give yourself permission to write a “crappy first draft”. Anne makes a great point — just start writing, and worry about editing it later.

When you’re ready to publish, give your post three to five tags that describe your blog’s focus — writing, photography, fiction, parenting, food, cars, movies, sports, whatever. These tags will help others who care about your topics find you in the Reader. Make sure one of the tags is “zerotohero,” so other new bloggers can find you, too.